연구동향 분석

Research of circuit manufacturing for new MID technology development

윤해룡 김호찬 이인환 2017년

논문상세정보
    • 저자 윤해룡 김호찬 이인환
    • 제어번호 104302703
    • 학술지명 JOURNAL OF MECHANICAL SCIENCE AND TECHNOLOGY
    • 권호사항 Vol. 31 No. 12 [ 2017 ]
    • 발행처 대한기계학회
    • 자료유형 학술저널
    • 수록면 5737-5743
    • 언어 English
    • 출판년도 2017
    • 등재정보 KCI등재
    • 판매처
    유사주제 논문( 0)
인용/피인용

' Research of circuit manufacturing for new MID technology development' 의 참고문헌

  • Transient Lubrication of Piston Compression Ring during Cold Start-Up of SI Engine
    Ali Usman International Journal of Precision Engineering and Manufacturing-Green Technology 3 1 81-90 [2016]
  • Thermal performance of high brightness LED array package on PCB
    K. C. Yung International Communications in Heat and Mass Transfer 37 1266-1272 [2010]
  • The introduction of powder blasting for sensor and microsystem applications
    E. Belloy Sensors and Actuators A: Physical 84 3 330-337 [2000]
  • Temperature-Dependent Mechanical Properties of ABS Parts Fabricated by Fused Deposition Modeling and Vapor Smoothing
    장성욱 International Journal of Precision Engineering and Manufacturing 18 5 763-769 [2017]
  • Process repeatability in abrasive jet micro-machining
    A. Ghobeity Journal of Materials Processing Technology 190 1-3 51-60 [2007]
  • Optimization of Hybrid Renewable Energy Power Systems: A Review
    Sung-Hoon Ahn International Journal of Precision Engineering and Manufacturing-Green Technology 2 1 99-112 [2015]
  • Noise Analysis for PCB Design
  • New Paradigms in Cellular Material Design and Fabrication
    유동진 International Journal of Precision Engineering and Manufacturing 16 12 2577-2589 [2015]
  • Multiphase Design Exploration Method for Lightweight Structural Design: Example of Vehicle Mounted Antenna-Supporting Structure
    장성우 International Journal of Precision Engineering and Manufacturing-Green Technology 2 3 281-287 [2015]
  • Microstructure and composition of pulsed-pelated metals and alloys
    D. Landolt Surface Coatings Technology 169 8-13 [2003]
  • Laser Assisted Milling Device: A Review
    이춘만 International Journal of Precision Engineering and Manufacturing-Green Technology 3 2 199-208 [2016]
  • Investigation into the Influence of Feeding Parameters on the Formation of the Fed-Powder Layer in a Powder Bed Fusion (PBF) System
    이호진 International Journal of Precision Engineering and Manufacturing 18 4 613-621 [2017]
  • High quality mechanical etching of brittle materials by powder blasting
    P. J. Slikkerveer Sensors and Actuators A: Physical 85 1-3 296-303 [2000]
  • Fabrication of a Micro-lens Array with a Non-layered Method in Projection Microstereolithography
    박인백 International Journal of Precision Engineering and Manufacturing 11 3 483-490 [2010]
  • Establishment of PCB industry technology base
  • Design and Experimental Verification of Flexible Plate-Type Piezoelectric Vibrator for Energy Harvesting System
    박정현 International Journal of Precision Engineering and Manufacturing-Green Technology 3 3 253-259 [2016]
  • A study on the lowering method of PCB radiation field
    Y. T. Han [2005]
  • A study on the lowering method of PCB radiated electromagnetic field
    Y. T. Han [2005]
  • A study on the influence factors on the customer intention to continue in the PCB industry
    J. K. Jung [2014]
  • A study on composite plating of nano silica permalloy using electroplating method and composite plating of nickel titanium nioxide
    S. Y. Park [2013]
  • A Study of Post-Processing Methods for Improving the Tightness of a Part Fabricated by Fused Deposition Modeling
    조광호 International Journal of Precision Engineering and Manufacturing 17 11 1541-1546 [2016]
  • 3D MID 크루즈 컨트롤 스위치의 개발
    고형주 [2014]